biosolids

Biosolids Odor Control via Hydrogen Peroxide

Project Scope

A Midwest wastewater treatment plant was struggling with problematic hydrogen sulfide (H2S) levels at two points within their facility arising from biosolids processing. The factors driving the need for H2S control included worker safety, corrosion of electronics and concrete, implied regulatory limits and odor control. Along with normal residential and commercial flows, the facility also receives unpredictable slugs of high biological oxygen demand (BOD) wastewater from agricultural industries and handles septage hauler loads from a wide radius. USP Technologies (USP) implemented a full-service hydrogen peroxide (H2O2) solution with operator-adjustable dosing options to account for the unpredictable sulfide loadings and to lower H2S to acceptable levels at both their biosolids holding tank and dewatering building.

biosolids

Technology

H2O2 is ideally suited to remove H2S from wastewater solids, provided that sufficient contact times are available – typically 2-5 minutes prior to the dewatering device. The efficiency of treatment depends upon the available reaction time, the initial level of H2S and the relevance of non-H2S odors. Under optimal conditions, effective dose ratios are about 5 parts H2O2 per part aqueous sulfide, and can be reliably estimated through beaker tests. The chemical reaction is as follows:

H2S + H2O2 → S0 + 2H2O

Background

A biosolids holding tank receives all biosolids awaiting dewatering at the plant’s two belt filter presses. The tank is generally emptied every one to three days depending on biosolids generation rates correlated with industrial discharge volumes. The biosolids entering the tank, especially from the gravity thickeners, contain a significant sulfide load throughout the entire year. The holding tank employs mechanical mixing and aeration to minimize further sulfide generation, however, this causes extreme volatilization of H2S, exceeding 500 ppm. Previous control methods, including iron salt addition and “in-situ scrubbing” using a hydroxyl ion generating system only provided limited success in achieving desired targets.

Compounding the challenge, the radicals generated interfered with the proper measurement of H2S. From the holding tank, biosolids are pumped to a dewatering building housing two belt filter presses. The turbulence of these belt filter presses causes most of the sulfide present to volatilize. A wet scrubber was installed and used for years to control the H2S, however, by 2014 it was at the end of its serviceable lifespan.

Solution

USP was invited to visit the facility to determine a more effective treatment strategy. Bench scale dose response tests utilizing shake tests were then conducted to determine theoretical hydrogen peroxide dosing needs and possible reaction times from several injection points. The optimal injection point was determined to be at the biosolids pump outlet, which provided approximately 3 minutes of reaction time before reaching the belt filter presses.

Shortly afterwards, a full-scale H2O2 storage and dosing equipment system was installed. The H2O2 pumps were connected by relays to the biosolids pumps to ensure that H2O2 only dosed while the biosolids pumps were running. The program was demonstrated to be effective within the first hour of operation, with H2S levels brought down below 1 PPM both above the belt filter presses and within the dewatering building’s main room. The program continued with dosing rates throughout the first six months ranging from 1.5 to 6 gallons/hour.

In addition, the operators were trained on how to both raise and lower dosing rates based on the observed H2S levels to mitigate variable industrial loadings. The removal of H2S from the dewatering facility eliminated the need for a costly replacement of their wet scrubber, and the customer invited USP to co-present our success story at their state conference.

Read More

Biosolids Odor Control at Holding Tank and Belt Filter Presses via Hydrogen Peroxide

USP Technologies

5640 Cox Rd.

Glen Allen, VA 23060

Toll-free (800) 851-8527

Phone (804) 404-7696

 View a Map

USP - Canada

3020 Gore Road

London, Ontario N5V 4T7

Toll-free (800) 851-8527

Phone (804) 404-7696

 View a Map

Version WPE

Contact Us

Our sales engineers are ready to help you find the right solution. Fill out the form to connect with your local USP Technologies representative.
  • This field is for validation purposes and should be left unchanged.

Sign Up For Our Newsletter

Subscribe for exclusive news, products, innovations, events and educational resources sent right to your inbox.

  • This field is for validation purposes and should be left unchanged.